With regard to airborne particles with an aerodynamic diameter of less than 10 µm (PM10), in countries in the European Union, the mass of brake emissions equals approximately 8–27% of the total traffic-related emissions. Using a research methodology combining tests at different scale levels with contact mechanics simulations and PM10 chemical characterization, the REBRAKE EU-financed project had t

Running-in process of low metallic brake pads and cast iron discs are investigated using full scale inertia brake dynamometer designed for particle emission studies. The airborne particles are measured using ELPI+ and collected on filters. The pads and disc contact surfaces are studied using microscopy techniques. It is observed that the particle emissions from the new pads and discs are significa

In the EU, PM10 from the wear of disc brakes can contribute up to 50% of the total non-exhaust emissions from road transport. The wear originates from the contact surfaces of the friction material and the disc. One possible way to decrease PM10 emissions is to change the materials of the contact pair in terms of composition and coatings. The wear and particle emissions of three novel friction mate

Airborne particulate matter emitted from motor vehicle brakes is a contributor to urban air quality. Therefore, a method to rank brake pairs (pads and rotors) with respect to their particle emission factors in a reliable way is needed to develop a low-emission disc brake. A novel inertial disc brake dynamometer designed for brake particle emission studies, a modified SAE J 2707 cycle, an electrica

Airborne particulate emissions originating from the wear of pads and rotors of disc brakes contribute up to 50% of the total road emissions in Europe. The wear process that takes place on a mesoscopic length scale in the contact interfaces between the pads and rotors can be explained by the creation and destruction of contact plateaus. Due to this complex contact situation, it is hard to predict h

Brake-related particulate matter contributes considerably to the non-exhaust emissions of the transport sector in urban areas of the world. The airborne particle emissions from automotive brakes currently lack any proper regulations. Future regulations require test stands, test cycles and particle instruments to be suitable for measuring the brake emissions. This present work focuses on the design

Airborne wear particles originating from disc brakes are among the main contributors to non-exhaust emissions. The macroscopic wear behaviour of disc brakes can be explained by the growth and destruction of mesoscopic contact plateaus. The pad wear and temperature has earlier been simulated using a cellular automaton mesoscopic approach. The present paper seeks to refine the simulation approach to

Airborne particle emissions from automotive disc brakes, one of the main sources of urban particulate matter, adversely affect health. Field measurement of brake particles is complicated, as various particle sources (such as tailpipe emissions, resuspended road dust and tyre wear) can interfere. Brake particles are usually measured on dyno benches or in model-scale tests in controlled environments

Particle emissions originating from the sliding disc brake contact in disc brakes are a main contributor to PM10 in Europe. The macroscopic friction and wear behaviour can be explained, at the mesoscopic scale level, by the growth and destruction of contact plateaus. This paper further develops a cellular automaton that describes the mesoscopic contact situation by implementing friction, wear, and

Airborne wear particles originating from disc brakes are one important contributor to the concentration of airborne particles in urban environments. It is therefore of interest to improve the knowledge of these particles. The purpose of this article is to investigate the concentration and size distribution of the airborne wear particles generated from the contact between a low-metallic pad materia

Based on the comparative analysis of the experimental values determined for the tribological parameters for the three novel nano-porous composition base and two conventional brake lining materials while friction with the grey cast iron disc, it was shown the considerable high tribological efficiency of the novel nano-porous composition base lining materials in comparison with the conventional (fro

Brake pads on wheel-mounted disc brakes are often used in rail transport due to their good thermal properties and robustness. During braking, both the disc and the pads are worn. This wear process generates particles that may become airborne and thus affect human health. The long term purpose of 'Airborne particles in Rail transport' project is to gain knowledge on the wear mechanisms in order to

Wear particles originating from disc brakes contribute to particulate concentration in the urban atmosphere. In this work novel nanoporous composite-based and conventional brake materials were tested against cast-iron discs in a modified pin-on-disc machine. During testing airborne wear particles were measured online and collected on filters, which were analysed using SEM and EDX. The morphology o

Since brake wear is an important contributor to the concentration of airborne particles in urban atmospheres, it is important to increase our understanding of the origin of these particles. The contact situation between the pad and disc is complicated. Metal fibres in the pad (or other hard materials) form stable contact plateaus, which carry the main part of the load. A flow of wear particles in

Much attention is given to the consequences of airborne particles on human health and well-being. Wear is one source of airborne particles and contributions in the urban environments from wheel-to-rail contacts and disc brakes cannot be neglected. Traditionally, mechanical wear has been associated with the generation of particles of diameters of some microns. However, the research described has fo

During braking, both the rotor and pads experience wear, generating particles that may become airborne. In field tests, it is difficult to distinguish these particles from others in the surrounding environment, so it is preferable to use laboratory test stands to study the amount of airborne wear particles generated. The purpose of this work is to investigate the possibility of separate, capture,

Most modern passenger cars have disc brakes on the front wheels. Unlike drum brakes, disc brakes are not sealed off from the ambient air. During braking, both the rotor and the pads wear, and this wear process generates particles that may become airborne. In field tests it is difficult to distinguish these particles from others in the environment. It is thus preferable to conduct tests using labor

A novel test method was used to study the concentration and size distribution of airborne wear particles from disc brake materials. A pin-on-disc tribometer equipped with particle counting instruments was used as test equipment. Material from four different non-asbestos organic (NAO) pads and four different low metallic (LM) pads were tested against material from grey cast iron rotors. The results

Unga forskare som vill göra akademisk karriär står inför många utmaningar. Deras tillvaro präglas av osäkra anställningar, motstridiga krav och begränsade erfarenheter av att stå på egna ben. Många befinner sig dessutom i familjebildande ålder. Kunskap om hur man kan göra för att må bra och nå framgång på sina egna villkor är sällsynt – få forskare låter andra få en inblick i deras forskartillvaro

During braking, both the rotor and the pads are worn in disc brakes. This wear process generates particles which may become airborne. In passenger car field tests it is difficult to distinguish these particles from others in the surrounding environment. It may therefore be preferable to use laboratory test stands and/or simulation models to study the amount of airborne wear particles generated. Th